Derkim Thermal Insulation Board Plaster

Description: Cement-based polymer modified and added chemicals and high strength, durable movement is a thermal insulation board plaster.

Uses: applied to all kinds of interior and exterior plaster is used for thermal insulation plate.

Preparation: Application of surface roughness to be made, water absorption, stability is checked beforehand. Locations surface voids and repairs to be performed repairs done previously. The surface plaster dust, dirt, debris is cleaned from factors such as oil.

Mixing and Application: 6 – 7 liters. Clean water is discharged into the dust portion on the container and slowly added to the mixture and mixed until it becomes a homogeneous consistency. Low speed mixer is used to mix. To mix at a high speed prevents a homogeneous consistency. Wait 5 minutes after the maturation time is ready for use again stirred slurry. On Thermal Insulation Board with the help of prepared mixture of plaster trowels 2 or 3 mm. thickness is driven in. PVC mesh, properly adhered to the plaster. Plaster mesh and plate is secured to the substrate with the help of plastic anchors. This practice 2 hours after aragonite Thermal Insulation Board Plaster is applied with a trowel onto the net again and corrected the following floating. 24 hours after this application can be any dye or applications.

Application tools should be washed with water after application. On the application process can not be expired material and the surface must be cleaned. Hardened and used material in the vessel has completed the outlet.

 Issues to be considered:

• Application temperature + 5 ° C / + 35 ° C should be the limit.

• The application surface of dust, dirt, spills should be cleaned of factors such as oil.

• Material must be mixed with a maximum of 120 speed mixer assistance.

• The mixture should be consumed within 2 hours.

• any contribution material outside material into the water (lime, sand, cement) should never be placed.

• should not be stacked more than 8 bags. Must be stored unopened in its original packaging stored in dry and dry.

• External factors (rain, sun, wind GB.) It is more durable than against the old plaster.

• the application and the application surface after application of external factors (wind, sun, moisture) must be protected.

• Application during protective equipment (clothing, gloves) should be used.

• Hand, eye and body contact should be avoided, wash immediately with plenty of water in contact with eyes, seek medical attention if necessary.

Binder: Cement-Based

Appearance: Powdered

Color: Gray

Mixing ratio: 25 kg product an average of 6 – 7 liters. admixed with water.

Amount of consumption: the average for 1 m2 4 – 4,5 kg.

Skinning Time: 60 minutes

Fresh mortar Hollow Unit Weight: ≥ 1150 kg / m3

Hardened Cement Based Plaster’s Hollow Unit Weight: 1.57 ± 10% kg / m3

Sieve Analysis: 1 mm. screens at most 1%

Bending strength: ≥ 2.0 N / mm2

Compressive strength: ≥ 6.0 N / mm2

Thermal Insulation Board Adhesion: ≥ 0.08 N / mm2

Water Absorption: ≤ 0.5 (kg / m2.dakik 0.5)

Water Vapor Permeability Coefficient: ʮ ≤ 15

Thermal Conductivity: EN 1745 TABLE A.12 BY P: 50% (λ10, dry) 0.47 W / mK

Reaction to fire: A1 <1%

Packaging: 25 kg. (3 times in kraft bags, as Stretching)

Shelf life: dry and moisture environment as the production date is 1 year.

Storage: Store in dry and humid conditions with unopened package stored stacked on top of more than 8.

Ripening time: 5 minutes

Potlife: Depending on the ambient conditions can be used after mixing for 2 hours.

Derkim Thermal Insulation Plate Adhesive

Description: It is an agglution mortar material with high stability which is used in agglutination of heat insulation boards.

Fields of Usage: It can be used in agglutination of every kind of heat plate implemented on both inside and outside facades.

Application: 25 kg. Derkim thermal insulation plate adhesive is mixed with approximately 6 liters of water with a low-speed mixer until a homogenous mixture has been obtained without any roundish lumps. This mixture is left to settle approximately for 10 minutes and after it is mixed again, it is ready to be used. Dust, dirt, remnants etc. on the surface on which the mortar will be applied should be cleaned. The mixture is put at the back of the insulation board in a way that there will be one heap for each corner and three heaps fort he middle or the agglutination can be made by spreading the mixture with trowel to the edge of insulation board and putting heaps in the middle. According as the weather conditions, 24-36 hours after the agglutination process, plastering can be applied. At least 35-40% percent of the insulating board with the adhesive should be applied at the back of the board.

Cautions and Precautions

• Application temperature should be between +5 and +35 C degrees.
• Application surfaces should be free from elements, such as dust, dirt, sweeps, oil etc.
• The mixer’s working rate should be maximum 120 speed.
• The prepared mortar should be consumed within 2 hours
• No additives other than water should be put into the material
• The surface should be protected from wind, water and sunlight during application
• The cement based materials shouldn’t be breathed directly and their contact with skin should be avoided. During the process, protective clothes should be put on

Rates of Mixtures: For a package of 25 kg. it is mixed with 6-7 liters of water

Consumption Amount: Averagely 3,5-4,5 kg. for per 1 m2

Color: Gray

Pot Life: 2 hours

Shelf Life: 1 year in dry and humid-free environment

Stocking: Max. 8 packages can be piled

Package: 25 kg. craft package